THC 24V Arc Voltage Plasma Torch Height Controller fr Plasma CNC Cutting Machine

Description

Store category
Sign Up Now !
You may also like
Product Description
THC 24V Arc Voltage Plasma Torch Height Controller fr Plasma CNC Cutting Machine
Instroduction:
XPTHC-100V is a brand new design THC controller, can fully replace the old version of XPTHC-100III. Based on the old version
’s function, this new version is with many new function/changes as below.
This arc voltage plasma torch height controller supports almost all plasma cutters on the market like Thermal Dynamics, HD plasmas HPR130, 260, Ultra-cut series, etc.
Also, it supports all CNC cutting controllers on market, like Burny, industrial level controllers or Mach3, because it can start Auto Height control with or without Auto enable signal from CNC(but with Auto enable/disable signal from CNC, THC would work better).
No software needed.
Basic parameter:
-Input Power: AC24V±5%, 50Hz/60Hz
-Down/Up Motor: DC24V DC MOTOR
-Motor Drive: PWM
-Output Current: 1A-4A, Load capacity: 100W.
-Working temperature: -10 to 600C
-Voltage Divide ratio: 100:1
-Control accuracy: ±1V to ±3V
-Size: 320mm*260mm*90mm
-The speed of lifting: 1000mm/min to 4000mm/min.
Basic functions:
A. Auto Initial Height Sensing(IHS).
Torch Retaining Cap IHS and Proximity Switch IHS (NPN and PNP),
Proximity Switch IHS is backup for Torch Retaining Cap IHS for cutting dirty/rusty workpiece, anti-collision torch clamp needed(optional).
B. Torch Anti-Collision Function(requires to work with anti-collision torch clamp)
No matter it is on Auto Control Model or Manual Control Model, when torch head touches the workpiece, THC would automatically lift torch up to IHS height.
C. Freeze Auto Height Control on Corner Signal.
The controller can recognize Corner Signal from CNC and freeze Auto Control Model on receiving this signal, and we have a unique design to backup this function.
D. Lifting torch Up on IHS Disabled status.
On IHS Disabled status, jogging torch head down until it reaches workpiece, when Arc Starts, torch head would lift up automatically to the Set Height set via the button SET-IHS.
E. Lifting Torch Up on TURN ON or Arc Off.
When CNC is TURN ON or Plasma Arc Off, THC would lift torch up for 2 seconds, please notice this Function during commissioning, avoiding the possible damage of limit switch or lift device.
F. Set Pierce Delay Time.
Set Button Set-PIERE (set Pierce delay time), to delay output this signal, it is a switch signal, set to detect arc voltage lead in THC. Once THC detect arc lead in, it send arc ok signal to CNC to start cut.
G. Manual Operation.
Many functions can be manually operated on the operation panel, such as, set Auto/Manual mode of THC, manually control torch Up and Down, IHS test, Arc Start test,.etc.
H. Arc Voltage Divide.
Isolation Voltage Divide, the Voltage Divide ratio is 100:1/50:1. Once Isolation Voltage Divide function damaged, user can also use Non-isolation Voltage Divide on our voltage divider.
1.XPTHC-100V is with much more simple setting method. P0-P9 data can be set directly on the control panel, at the meantime, old version’s quick-setting knob is remained. Restore the default factory parameters: In the stopped state, press the "AUTO" and "MENU" keys at the same time, and then click the "IHS" button.
2. XPTHC-100V’s motor wiring method is the same as the old version, but adding limit logic modify setting parameter P6 and current limit state display. Limit logic’s default parameter is PNP effective(P6:1), same as the old version.
3. XPTHC-100V’s proximity switch’s wiring method is the same as the old version, but no need to set the proximity switch’s mode on the initial jumper, just need to modify the P9 value on the control panel.
4.XPTHC-100V’s “TO CNC” port: Pin1, 2, 3, 4, 5, 8 is the same as the old version’s, but Pin6 is for Arc feedback output, can be connected to CNC’s Arc feedback input directly; Pin7 is “Collision” output, can be connected to CNC’s collision input directly. There is built-in Dynamic Piecing function in the controller, so we removed the old version’s outer dynamic piecing function (Pin9&Pin10).
5. XPTHC-100V’s Torch Retaining Cap IHS’ wiring is basically the same as the old version, but we added a “High Voltage Isolator” for high frequency Striking Arc Plasma’s Torch Retaining Cap IHS; we also added torch tip’s IHS function on XPTHC-100V: the red IHS wire on the “High Voltage Isolator” can be directly connected to the plasma torch’s strike arc wire(no need to tie it on the torch tip). Under the Torch Retaining Cap IHS & Torch tip IHS mode, the controller has under-water IHS function: need to modify P0’s value to be “1”, the “High Voltage Isolator” should be installed beside the plasma torch.
6. XPTHC-100V’s power supply is the same as the old version, can be powered by DC24V or AC24v.
7. XPTHC-100V’s voltage divider’s installing size is the same as the old one, but voltage dividing ratio changed to be 50:1(to make its controlling more precisely), meanwhile
voltage divider’s power supply changed to be AC/DC 24V(the old version’s is AC220v), can share the same power supply as the controller’s, please pay much attention on this change!
When connect the voltage divider to the controller, the 4-pin connector’s(“TO PLASMA”) wiring can be the same as the old version’s, but our new wiring method for it would make it with much better anti-jamming performance
Panel Parameter Setting
Other optional
Anti-collision function torch clamp(Not included)
Anti-collision function torch lifter(Not included)
Note:
Your valid phone number is very important for the shipping,please provide it when you order
!
Any customs duty applied to the parcel should be covered by the buyer.
As has been stated on the eBay item description, Import duties,
taxes and charges are not included in the item price and shipping charges.
These charges be at the buyer responsibility. meanwhile the customs tax depend on the buyer local customs office.
The product can be shipped by DHL or other Express, but a surcharge of US will be applied on the shipment when your location is remote. Remote is defined as islands and highlands; or a post code/zip code that is difficult to serve; or a suburb/town that is distant, inaccessible or infrequently served.
Note:
We are looking forward to a further extension of pleasant business relation. If you have any questions after receiving the goods or need something, please contact us,we will do our best to make you satisfied.
1X Arc Voltage Torch Height Controller Unit
1X Voltage Divider
1X Accessories(Connectors)
Shipping
1.Item will be shipped within 3 business days of cleared payment via Post Airmail.
2.Only shipped to buyer's PayPal address, please confirm your address on PayPal before you bid.
3.Usually takes 7-20 business days to most Countries: US, Canada, UK, Australia and Europe.
4.Optionally, Express Shipments with tracking service via EMS/DHL/UPS with a quoted delivery time of 5 to 7 business days is also available .
Payment
We ONLY accept Paypal.go to
paypal
account
Any customs duty applied to the parcel should be covered by the buyer.
eCheque will be held until cleared
We appreciate prompt payment and look forward to your business in the future.Unpaid item will be filed without receiveing payment in 7 days from listing ended.
Warranty
This item is ALL BRAND NEW and in the original factory box and packing,All products have been checked and packaged in good condition before dispatch.
12 months Manufacture's Warranty for defective items (excluding items damaged and/or misused after receipt)
Defective items Must BE reported and returned to us within the warranty period(and the original package.).we will give you a return ID.Meanwhile Please tell us what the defect is,to eliminate improper use.
Return shipping fee be responsible from buyer
{{titlepaymentterms}}
{{titleshippingterms}}
{{titlesalesterms}}
{{titleaboutus}}
{{titlecontactus}}
{{titlepaymentterms}}
{{paymentterms}}
{{titleshippingterms}}
{{shippingterms}}
{{titlesalesterms}}
{{salesterms}}
{{titleaboutus}}
{{aboutus}}
{{titlecontactus}}
{{contactus}}
On Nov-12-17 at 17:32:08 PST, seller added the following information: